The technology of the new Mercedes-Maybach S-Class
- 9 Pictures
- 3 Videos
- 4 Documents
The new Mercedes-Maybach S-Class: Under the microscope: DIGITAL LIGHT
High-resolution light projection with innovative assistance functions
DIGITAL LIGHT as a technology of the future celebrated its world debut in small-series production of the preceding model, but is now in full series production with the new S-Class generation. This headlamp technology (optional equipment) allows completely new functions, e.g. the projection of guidelines or warning symbols onto the road ahead. In each headlamp, DIGITAL LIGHT has a light module with three extremely powerful LEDs with light that is refracted and directed by 1.3 million micro-mirrors. The resolution is therefore more than 2.6 million pixels per vehicle.
The micro-mirrors occupy the same area as a thumbnail. A control unit with a powerful graphic processor uses an HDMI‑like connection to generate a continuous video stream to the mirrors. Digital Light therefore uses the technology of video projectors. This innovative headlamp in the Mercedes-Maybach S-Class can be recognised by its concave lens, the lettering and shining blue floor facing.
The beam divided into 1.3 million pixels makes absolutely precise light distribution possible. It makes Highbeam Assist over 100 times more precise then 84-pixel light when excluding oncoming traffic or road signs from the light beam. Light/shadow graduations and the light distribution of all the other adaptive light functions are also realised with considerably more precision, optimising illumination by e.g. fog light, motorway light or city light.
These assistance functions are of particular significance1:
- Warning of recognised roadworks by projecting an excavator symbol onto the road surface
- Aiming a spotlight at pedestrians detected at the roadside as a warning
- Traffic lights, stop signs or no-entry signs are pointed out by projecting a warning symbol onto the road surface
- Assistance on narrow road lanes (roadworks) by projecting guidelines onto the road surface
The topographic light takes hills into account on the basis of navigation maps, especially crests and depressions: when cresting a hill, for example, the headlamp does not shine upwards but is pivoted down parallel to the road surface. In depressions the light beam is raised to maintain the desired range.
DIGITAL LIGHT welcomes and says farewell to the driver with a special light show.
1Owing to road traffic regulations, the availability and functions of these new assistance functions may be restricted on a market-specific basis.
The new Mercedes-Maybach S-Class: Acoustic comfort
Extraordinarily quiet and low in vibrations
In the rear, the preceding model was the world's quietest saloon car when it was launched in 2015. The new Mercedes-Maybach offers even more acoustic comfort. The NVH (noise, vibrations, harshness) characteristics were tested in e.g. the technology centre for acoustics and vibrations (TAS) in Sindelfingen and the Test and Technology Centre (PTZ) in Immendingen.
The new luxury saloon further improves the very good NVH performance of the new S-Class generation. Here, too, the rigidity of the bodyshell is the basis for the outstanding noise and vibration comfort. Other S-Class features such as double sealing of the cable grommets passing through the firewall, generous firewall insulation and acoustic foam in certain sections of the bodyshell have also been adopted.
The extended NVH measures in the Mercedes-Maybach S-Class mainly benefit the rear section. Additional absorbent foam is installed in the area of the rear wheel arches, for example, as these have a new cavity not shared by the brother models. The additional, fixed triangle windows in the C-pillars have thicker laminated glass, as they are in close proximity to the heads of rear passengers.
Noise-optimised tyres with foam absorbers are available for the Mercedes-Maybach on request. Foam material on the inside of the treads acts like a sound suppressor, making the interior even quieter. In addition, thermal and noise insulation laminated safety glass which also reflects infrared light is available all-round as optional equipment. The additional membranes between the layers of laminated safety glass also serve to reduce wind noise. They reduce noise reflected from guardrails or oncoming traffic as well.
Active road noise compensation is within the Daimler Group for the first time. The system reduces unwanted low-frequency noises using counter-phased sound waves (see separate section).
Mercedes-Benz engineers test vehicle acoustics in the technology centre for acoustics and vibrations (TAS) in Sindelfingen. This testing saw the first use of "Dascha", a development dummy which self-generates the noises to be measured (Daimler noise source).
The TAS enables noises inside and outside the vehicle to be measured and analysed in different situations - here are some examples:
- In one test laboratory, contact-free, fully automatic vibration measurements are carried out. The vibrations on surfaces are scanned with the help of lasers, then visualised as by a thermal imaging camera. The laser scanners are mounted on the arm of a robot moving along linear axes. (Simulated) excitation of individual vehicle components is carried out by a shaker. The system can measure both individual components and entire vehicles. To this end a crane is mounted on the laboratory ceiling.
- The external noise roller dynamometers use microphone arrays, some of which have over 800 microphones connected in series. These enable passing noises to be simulated although the vehicle is stationary, whatever the time of year or weather. In addition the noise sources can be analysed. Sound-absorbing cones on the walls ensure the quietest possible room acoustics very similar to a free field.
- High-frequency road impulses can be simulated at all four vehicle wheels on the acoustic and vibration comfort test rig. This takes the form of a flat surface test stand, and comes closer to reality than a roller dynamometer in terms of tyre-to-road contact. Different vertical and horizontal impulses are transferred to the wheels to simulate uneven road surfaces, including slab joints on motorways and rough asphalt.
- The rain noise test station examines the noises generated by rainfall of different intensities on e.g. the roof and windows. Precisely 1648 water nozzles are installed in the high ceiling for this purpose.
By means of simulations and measurements in the TAS, acoustic engineers are already able to achieve a high level of maturity before test vehicles are taken to e.g. the Test and Technology Centre (PTZ) in Immendingen. The asphalt surface of its acoustic test track has precisely the friction coefficient defined by the ISO 362 and ISO 10844 standards. Alongside acoustic testing, this also allows acoustic measurements to be carried out for certification purposes. Bays on the edge of the test track provide spaces for microphones.
The new Mercedes-Maybach S-Class: Under the microscope: Active road noise compensation
Even quieter thanks to sound waves
With Active road noise compensation, the interior of the already very quiet Mercedes-Maybach S-Class becomes even quieter. In a similar way to headphones with noise suppression, the system reduces unwanted low-frequency noises using counter-phased sound waves. The bass speakers of the Burmester® high-end 4D surround sound system are used for sound reproduction.
Impulses from the road surface generate low-frequency noises which are perceived as droning or throbbing in the interior. In the Mercedes-Maybach S-Class with active road noise compensation, there are six acceleration sensors in the suspension system. These send reference signals to the control unit. Using this information, a special algorithm calculates the necessary counter-noise in advance. The requisite sound waves phase-shifted by 180 degrees are reproduced by the bass speakers of the Burmester® high-end 4D surround sound system.
A corresponding BUS system transfers the audio signals at "supersonic" speed. This is because they must reach the human ear at the same time as the road noise. Only around three milliseconds are available for this.
As the noise characteristics can change when the road surface changes or the speed varies, the system also uses four interior microphones for monitoring and adaptation. These additional microphones are very close to the passengers, directly next to the microphones of the hands-free system.
The counterwaves of the active road noise compensation cannot be heard by the occupants. However, they are also generated if the Burmester® high-end 4D surround sound system appears to be switched off, as the amplifiers are always in operation. Active road noise compensation is automatically switched off at low speeds below around 20 km/h, and above around 180 km/h when wind noises predominate. No counterwaves are generated when side windows or the sunroof are open, as this changes the control parameters in the interior.
Active road noise compensation was developed together with the Harman subsidiary HALOsonic.
The new Mercedes-Maybach S-Class: Suspension
Comfortable setup and surprising manoeuvrability thanks to rear-wheel steering
The AIRMATIC air suspension with level control and continuously adjustable damping ADS+ is standard equipment. Optional rear-axle steering with a steering angle of up to 10° improves manoeuvrability and reduces the turning circle by up to two metres. The optional, fully active E-ACTIVE BODY CONTROL suspension on a 48 V basis uses a stereo camera to scan the road ahead, and smooths out undulations. It also gives additional protection in the event of a lateral collision.
DYNAMIC SELECT has the additionally developed driving mode MAYBACH, which the Mercedes-Benz S-Class does not have. With this setting the power delivery is even more comfortable, making the journey even smoother and more relaxed:
- Gentler accelerator characteristics for Chauffeur mode
- Even more comfortable, low-shift transmission configuration
- Maximum comfort by starting off in 2nd gear
The setup of the AIRMATIC air suspension and E-ACTIVE BODY CONTROL is configured for maximum suspension comfort on all seats.
The vehicle level is kept constant
The standard-fit AIRMATIC air suspension responds particularly sensitively. It combines air suspension bellows with adaptive ADS+ dampers whose characteristics can be fully automatically varied at each individual wheel, in both the compression and rebound stages. This level control is part of AIRMATIC. It keeps the ground clearance constant, irrespective of the vehicle's load. To reduce aerodynamic drag and therefore fuel consumption, the suspension is automatically lowered at higher speeds.
Even better ride comfort and agility, as well as innovative functions such as raising the vehicle body in a lateral crash, are provided by the E-ACTIVE BODY CONTROL active suspension, which is combined with the standard AIRMATIC air suspension. It is able to control the spring and damper forces at each wheel individually. ROAD SURFACE SCAN monitors the road ahead with a stereo camera, and already adapts the suspension before the wheels cross uneven surfaces. Thanks to this predictive control, the vehicle body "floats" across undulations with practically no vertical movement. With the curve inclination function CURVE, the vehicle body leans into bends rather than tilting outwards. This imposes lower lateral forces on the occupants, further improving perceived comfort.
Both axles are capable of steering, thus reducing the turning circle
Naturally the generous interior of the Mercedes-Maybach S-Class requires corresponding external dimensions. To ensure manoeuvrability and precision even in confined spaces, it is equipped with rear-axle steering (optional equipment). This reduces the turning circle by up to two metres. Customers have a choice between two variants: 4.5° and 10° rear-axle steering. Instead of 13.4 metres, the turning circle is then 12.4 or 11.4 metres.
In models with the optional rear-axle steering, a front steering system with an approx. 15 percent more direct steering ratio is used with the well-proven four-link front suspension. Acting together with the rear-axle steering, this considerably reduces the steering action required and improves ride comfort even further. Agility and manoeuvrability are objectively improved, and at the same time the serene stability and precision of a long-wheelbase luxury saloon are further enhanced at higher speeds.
The new Mercedes-Maybach S-Class: Restraint and driving assistance systems
More protection before and during accidents
Especially in the Mercedes-Maybach S-Class, particular attention has always been paid to safety in the rear section. The innovative rear airbag demonstrates this: during severe frontal collisions, this standard feature can considerably reduce the loads acting on the heads and necks of seat belt wearing occupants on the outer rear seats. In day-to-day driving, new and extended assistance systems relieve driver stress as the situation requires when adapting the vehicle speed, controlling distance, steering and lane-changing. This enables the driver to stay alert for longer, and reach the destination more safely and comfortably. When danger threatens, driving assistance systems can respond according to the situation and mitigate the severity of possible collisions, or even avoid them.
The Executive seats in the rear feature
- Seat cushion airbags. These counteract "submarining" under the fastened seat belt.
- Beltbags (optional equipment). The inflatable belt strap spreads the incoming forces over a wider area.
- Belt extenders (optional equipment) make seat belt fastening more convenient.
- After fastening the belt, the belt comfort adjustment sets the restraining force of the safety belt to a particularly pleasant level. Belt tensioners and force limiters are standard equipment to help reduce the loads on the occupants.
- Frontal airbags. The rear airbags for both rear occupants are a new feature.
- Sidebags are also available in the rear to provide protection in the event of a severe side crash.
- Windowbags. Located in the area of the roof frame, these cover the large head impact area of both front and rear occupants.
In critical driving situations the PRE-SAFE® positioning function also moves the rear seats to a more favourable crash position. The active multicontour seats in the Seating Comfort package Rear provide additional protection in combination with PRE-SAFE®: if a critical driving situation is recognised, the PRE-SAFE® system can increase the pressure in the air chambers in the side bolsters of the multicontour seats. This fixes the occupants in a better seating position and reduces whiplash.
All-round safety on the front seats as well
The driver and front passenger each have a three-point seat belt with pyrotechnical inertia-reel tensioning and belt force limitation and, as part of the standard PRE-SAFE® system, electrically reversible reel tensioning including deselectable automatic belt adjustment. The belt is in particularly gentle contact with the occupant's body. In the event of a severe frontal impact, PRE-SAFE® Impulse can reduce the forces acting on the driver and front passenger. The system tensions the front belts at all three attachment points, restraining the occupants at an early stage.
The driver and front passenger also have front airbags, and the driver a kneebag. If the central electronic control unit detects a side crash, the windowbag and sidebag are deployed on the side of the vehicle where the impact occurs. To ascertain the lateral acceleration, the central crash sensor has support from exterior satellite sensors located at the base of the B-pillars. Pressure sensors in all four doors also help to estimate the severity of the impact.
In addition, the preventive, semi-reversible side restraint system PRE-SAFE® Impulse Side is installed as standard to protect the front occupants. Together with the familiar PRE-SAFE® protection concepts for frontal and rear collisions, PRE-SAFE® Impulse Side forms a kind of virtual crumple zone that extends all around the vehicle.
As only a limited crumple zone is available in the case of a side impact, and even before the crash, PRE-SAFE® Impulse Side can move the affected driver or front passenger away from the acute danger zone as soon as the system detects that a side collision is immediately imminent. For this purpose, air chambers in the side bolsters of the front seat backrest are inflated in fractions of a second. In addition, when a side impact with another vehicle threatens, the vehicle body can be raised by the E-ACTIVE BODY CONTROL suspension (optional) within a few tenths of a second. This directs the impact forces towards particularly resistant structures in the lower area of the vehicle During a severe side impact, the new centre airbag (available depending on country) positions itself between the driver and front passenger seat, reducing the risk of head contact. It is integrated into the driver's backrest in the middle of the vehicle. The centre airbag can be deployed as the situation demands when a severe side impact is detected.
Frontal airbags for both rear occupants for the first time
The rear airbag is an innovation by Mercedes-Benz. During severe frontal collisions, it can considerably reduce the loads acting on the heads and necks of occupants on the rear seats. The rear airbag uses an innovative concept to inflate and position the air cushion. The special tubular structure is rapidly inflated by compressed gas from a cold gas generator. The space between is filled with ambient air. The tubular structure itself has a content of approx. 16 litres. The effective volume of the space in between is up to 70 litres.
An airbag in the seat belt: the beltbag
The beltbag is an inflatable seat-belt strap that reduces the load on the ribcage in a front impact, and is thus able to reduce the risk of injury to passengers in the rear. Should the crash sensors detect a severe frontal impact, the airbag control unit triggers deployment and inflation of the beltbag. A gas generator then inflates the multi-layered belt strap with Velcro seams to nearly three times its normal width. The resulting larger surface area is able to better distribute the force acting on the seat occupant. The beltbag is used in exactly the same way as a conventional seat belt. However, this version of the belt strap differs from the standard belt and is very comfortable to wear thanks to its particularly soft edges.
An airbag for the seat: the seat cushion airbag
The airbag is located under the seat cushion upholstery, but on top of the plastic seat shell which is moved by the seat mechanisms. This means that the airbag is always in the right position relative to the occupant. Without additional measures, with the occupant in a reclined position on a flat seat cushion, there would otherwise be a danger of the pelvic area sliding beneath the belt strap (submarining) in an accident. This can be prevented by the cushionbag, as it raises the front section of the seat cushion upholstery.
Driving assistance systems
The basic functions of the systems in the Driving Assistance package included as standard can be found here. The main new features of the systems in the Mercedes-Maybach S-Class:
Active Distance Assist DISTRONIC
On all types of roads – motorways, country roads or in town – this intelligent system can automatically maintain a preset distance from vehicles ahead. New features:
- predictive speed regulation ahead of speed limits
- reaction to stationary vehicles on the road at driving speeds up to 100 km/h (previously: 60 km/h)
- selection of DISTRONIC dynamics in MBUX, independently of DYNAMIC SELECT
Active Steering Assist
This helps the driver to follow the driving lane at speeds up to 210 km/h. New features:
- additional lane recognition by a 360° camera
- significantly improved availability and performance on bends on country roads
- improved lane centring on motorways
- situation-specific off-centred driving (e.g. forming an emergency lane, but also following the road edge on country roads with no centre marking)
Traffic Sign Assist
In addition to conventionally signposted speed limits, this recognises overhead gantries and signs at roadworks. Warnings given when failing to stop at a stop sign and a red traffic-light are a new feature.
Active Lane Keeping Assist
In a speed range of 60 to 250 km/h, Active Lane Keeping Assist uses a camera to detect when road markings or road edges are crossed, helping the driver to avoid leaving the driving lane unintentionally. The system also intervenes if there is a danger of collision with recognised road users in the adjacent lane, e.g. with overtaking or oncoming vehicles. New features:
- reaction to road edges, e.g. a patch of turf
- particularly intuitive steering intervention
- adjustment of sensitivity via a menu (early, medium, late)
- the danger warning is reinforced by the active ambient lighting and the augmented reality head-up display
Active Lane Changing Assist
Active Lane Changing Assist cooperatively assists the driver of the new S-Class when moving to an adjacent lane. A lane-change to the right or left is only assisted if the sensors detect that the adjacent lane is separated from the present lane by an interrupted lane marking, and no other vehicles are recognised in the relevant danger zone.
Active Emergency Stop Assist
Active Emergency Stop Assist brakes the vehicle to a standstill in its own lane if it recognises that the driver is no longer responding to the traffic situation for a longer period. This still works if Active Distance Assist DISTRONIC with Steering Assist is not switched on. Other new features:
- belt tensioning and braking impulse as a final signal of impending braking action
- optional single lane change (at 80 km/h, no obstacles in adjacent lane)
ATTENTION ASSIST
This system included as standard is able to recognise typical signs of drowsiness and driver inattention, and displays a warning message prompting him/her to take a break. The additional microsleep warning is a new feature. This is based on analysis of the driver's eyelid movements by a camera in the driver display (only in conjunction with certain optional equipment). The microsleep warning function is already active from a speed of 20 km/h.
Active Brake Assist with cross-traffic function
Active Brake Assist uses the onboard sensors to register whether there is a risk of collision with vehicles travelling ahead, crossing or oncoming. The system can give the driver a visual and acoustic warning if a collision appears imminent. If the driver's braking response is too weak, the system can also assist by increasing the brake pressure as the situation demands, and also initiate autonomous emergency braking if the driver fails to respond. New functions include the turn-off function (e.g. crossing pedestrians when turning off), extension of the cross-traffic function to long‑distance routes (up to 120 km/h instead of 72 km/h) and warning/braking for oncoming traffic.
Active Blind Spot Assist and exit warning function
Active Blind Spot Assist can give a visual warning - and if the indicators are operated also an audible warning - of potential lateral collisions in a speed range from around 10 to 200 km/h. If the driver ignores the warnings and still initiates a lane-change, the system can take corrective action by one-sided braking intervention at the last moment if the speed exceeds 30 km/h. When the vehicle is stationary, the exit warning function can warn against exiting because a vehicle (also bicycles) is passing within the critical area. This function is available when the vehicle is stationary and for up to 3 minutes after the ignition has been switched off. As a new function, the danger warning is augmented by the active ambience lighting (also the exit warning function). Thanks to the cameras of MBUX Interior Assist, a danger warning can be given even if the driver or front passenger merely move a hand towards the door handle.
Evasive Steering Assist
Evasive Steering Assist can assist the driver when seeking to avoid another road user detected by the system in a critical situation. In the new S-Class, the system not only recognises stationary and crossing pedestrians, but now also takes account of pedestrians and vehicles travelling longitudinally, as well as cyclists. The speed range has been increased to 108 km/h (instead of 72 km/h), and assistance is also given on long-distance routes.
The new Mercedes-Maybach S-Class: The DRIVE PILOT
Conditionally automated driving becomes a reality
The home office will soon be mobile – also for the person at the wheel. At least if they drive a vehicle bearing the three-pointed star: for Mercedes-Benz wants to bring about the technical realisation and safe operation of an S-Class driving in conditionally automated mode and to meet the exacting legal requirements for what is known as a Level 3 system1. It is expected that from the second half of 2021 the Maybach will be able to drive in conditionally automated mode with the new DRIVE PILOT, in situations where traffic density is high or in tailbacks on suitable motorway sections in Germany. By taking pressure off the driver, this allows them to undertake secondary activities2 such as browsing on the internet or dealing with emails in the In-Car Office, and so win extra time. Mercedes-Benz goes a step further when it comes to parking: with the appropriate pre‑installation for the INTELLIGENT PARKING PILOT, the Maybach is ready for driverless fully automated parking (automated valet parking; Level 43).
With the DRIVE PILOT, conditionally automated driving at Mercedes-Benz is expected to enter series production from the second half of 2021. On suitable motorway sections and where traffic density is high, the DRIVE PILOT can offer to take over the driving, initially up to the legally permitted speed of 60 km/h. The controls needed for this are located in the steering wheel rim, on the left and right above the thumb recesses. When the driver activates the DRIVE PILOT, the system controls the speed and distance, and serenely guides the vehicle within its lane. The route profile, events occurring on the route and traffic signs are all assessed and taken into consideration accordingly. The DRIVE PILOT can also recognise unexpected traffic situations, and deal with them autonomously by evasive action within its lane or braking action.
With the LiDAR sensor and redundant systems
The DRIVE PILOT builds on the surround sensors of the Driving Assistance Package and comprises additional sensors that Mercedes-Benz considers indispensable for safe conditionally automated driving. These include LiDAR, an additional camera in the rear windscreen and microphones, which are particularly useful for recognising the flashing blue lights and special signals of emergency vehicles. As well as the sensor data, the DRIVE PILOT receives information about the road geometry, route profile, traffic signs and unusual traffic events (e.g. accidents or roadworks) from a digital HD map. This is made available by a back-end connection. The vehicle's location is determined using a highly precise positioning system that goes well beyond the usual GPS systems. The Mercedes-Maybach S-Class with the optional DRIVE PILOT also has redundant steering and braking systems and a redundant onboard electrical system, so that it remains manoeuvrable even if one of these systems fails and a safe handover to the driver can be ensured.
A powerful central control unit provides the necessary sophisticated software functions for conditionally automated driving. Artificial intelligence is used for image processing, for example. As part of the state-of-the-art safety architecture, all algorithms are calculated twice.
While using the DRIVE PILOT, the driver can turn away from what is happening on the road and engage in certain secondary activities, e.g. communicating with colleagues via In-Car Office, browsing on the internet or enjoying a relaxing seat massage. This is because in DRIVE PILOT mode, functions can be enabled that are otherwise blocked when driving.
Conditionally automated driving on suitable motorway sections where traffic density is high
When the vehicle approaches the end of a route section that is suitable for the DRIVE PILOT, for example a tunnel, or if other conditions change, perhaps the weather or the traffic situation (for example when a tailback begins to flow freely), the driver is prompted in good time to retake control. As a general principle, the driver must always be ready to retake control and immediately resume driving as necessary when the system prompts him/her to do so, or if it is obvious that the conditions for the intended use of the DRIVE PILOT no longer apply. Sleeping, looking to the rear for longer periods or even leaving the driver's seat are not permitted. To ensure that the driver is able to take control, the cameras of the driver display monitor movements of the head and eyelids.
If the driver fails to take back control even after increasingly urgent prompting, e.g. owing to a severe health problem, the DRIVE PILOT brakes the vehicle to a standstill in a controlled manner and with suitable deceleration. At the same time the hazard warning system and, once the vehicle has come to a standstill, the Mercedes-Benz emergency call system are activated and the doors and windows are unlocked, to make access to the interior easier for any first responders. Naturally the driver can also deactivate the DRIVE PILOT at any time without any prompting by the system. This is done via the steering wheel buttons, or by manually intervening in the vehicle's control functions.
The system is constantly improving
The top speed of a system with conditional automation in Germany is restricted by law to 60 km/h. However, the DRIVE PILOT is prepared for the possibility of permitting higher speeds as well via over-the-air updates in the future, where this is technically feasible and the legislative framework allows it. The general introduction of the DRIVE PILOT in other European countries, in the USA and China will follow gradually as the legal situation in each country provides for a surrendering of the driving task.
1SAE Level 3: the automated driving function takes over certain driving tasks. However, a driver is still required. The driver must be ready to take control of the vehicle at all times when prompted to intervene by the vehicle.
2The legally permissible secondary activities of the driver depend on the relevant national traffic regulations.
3SAE Level 4: Under certain circumstances (e.g. selected roads, not in any weather) the vehicle can manage all traffic situations by itself. No driver is required to be in the vehicle.
Pictures 9
Videos 3
Documents 4
- 38 Pages
- 345.8 KB
- 39 Pages
- 411.7 KB