The new Mercedes-Benz A-Class: The Technology
- 66 Pictures
- 3 Videos
Fuel consumption combined: 6.0 – 4.1 l/100 km Combined CO₂ emissions: 141 – 108 g/km
All the new A-Class models are powered by new, efficient engines: Two new four-cylinder petrol engines are available at market launch. Innovations in the M 282 with a displacement of 1.4 litres and up to 120 kW include cylinder shutoff (in conjunction with the 7G-DCT transmission) and the delta shape of the cylinder head. The second new petrol engine is the M 260 with a displacement of 2.0 litres, 165 kW and 350 Nm. New features include CAMTRONIC for the intake camshaft. Both petrol engine series have low-friction cylinder walls and a particulate filter as standard. Also new is the four-cylinder diesel (OM 608) with a displacement of 1.5 litres, up to 85 kW and up to 260 Nm. Its highlights are a near-engine mounted emission control system with AdBlue® technology, a turbocharger with optimised response time and water intercooling. A new 7G-DCT dual clutch transmission is also being introduced. Further new engines will follow. The fuel tank has a capacity of 43 litres as standard, with a 51-litre tank optionally available.
The following three engine variants will be available on the launch of the
A-Class, or shortly afterwards*:
- A 200 (120 kW/163 hp, 250 Nm; with 7G-DCT dual clutch transmission combined fuel consumption 5.1 l/100 km, combined CO₂ emissions 120 g/km) or six-speed manual transmission (combined fuel consumption 5.6 l/100 km, combined CO₂ emissions 133 g/km)
- A 250 with 7G-DCT dual clutch transmission (165 kW/224 hp, 350 Nm; combined fuel consumption 6.0 l/100 km, combined CO₂emissions 141 g/km)
- A 180 d with 7G-DCT dual clutch transmission (85 kW/116 hp, 260 Nm; combined fuel consumption 4.1 l/100 km, combined CO₂ emissions 108 g/km)
The new M 282 petrol engine: four-cylinder with cylinder shutoff
The new entry-level engine in the A 200 is the M 282 with a displacement of 1.33 litres. Compared to the previous 1.6-litre engine, the output of this all-aluminium engine has increased by up to eleven percent and the output per litre by no less than 25 percent. This engine excels with very compact dimensions, low weight and high static and dynamic rigidity. The turbocharger features an electronically controlled wastegate: thanks to flexible charge pressure control, it is also possible to set an optimum charge pressure under partial-load conditions.
This is the first four-cylinder Mercedes-Benz engine to feature cylinder shutoff (initially in conjunction with the 7G-DCT transmission). In the partial load range between 1250 and 3800 rpm, and depending on the power requirement, the intake and exhaust valves of the second and third cylinder are closed by valve clearance adjustment. The remaining two cylinders therefore operate under higher loads, and more efficiently. To minimise friction, the cylinder walls are coated using the patented NANOSLIDE® process. The piston skirts are given an Eco-Tough coating, a special graphite coating for optimised friction and high wear resistance.
Another special technical feature is the delta cylinder head, so called because of its shape. It is slightly higher when installed, but much narrower and lighter than conventional cylinder heads. Further advantages include the semi-integrated intake and exhaust manifolds, which allow compact construction. Daimler holds a patent for the compact arrangement of the high-pressure injection pump with a maximum of 250 bar. The multi-hole injection nozzles are centrally located in the combustion chamber, and injection occurs without the valves being subjected to the jet of fuel.
This new, high-compression four-cylinder engine has a particulate filter as standard. Particular effort was also devoted to noise emissions. The intake air duct features a Helmholtz resonator, the catalytic converter has insulating seals and the cover also has a noise-reducing role.
The new engine will initially be available with the 7G-DCT dual clutch transmission, and later also with a six-speed manual transmission and 4MATIC all-wheel drive.
The M 282 was developed by Mercedes-Benz in cooperation with Renault. It is produced at the Kölleda plant in Thuringia, Germany and in future it will also be produced in Beijing, China. Renault supplies the components of the long block engine.
The new M 260 petrol engine: premiere of CONICSHAPE®
The M 260 four-cylinder engine of the A 250 is essentially a further development of the previous M 270, with an output increase of over 6 percent compared to its predecessor. Its engine block of diecast aluminium with cast iron cylinder liners conceals a world premiere in large-scale production: CONICSHAPE®, also known in-house as "trumpet-honing". To further minimise piston friction and lower fuel consumption, the cylinder bore is widened at the lower end of the cylinder liners. The resulting, conical shape resembles the mouth of a trumpet. An innovative low-friction oil and optimised piston rings also reduce friction losses. To take account of the higher specific output, the pistons themselves feature cooling ducts. This also ensures more efficient combustion. The balance shafts for smooth engine-running are located in the lower section of the crankcase.
Also new in the aluminium four-valve cylinder head of the two-litre engine is CAMTRONIC, a variable valve timing system that allows two-stage adjustment of the valve lift on the intake side of the valve assembly. In the partial-load range, this variable valve lift adjustment allows less air to be fed to the combustion chamber with a smaller valve lift, which leads to lower gas cycle losses. In higher load ranges the system switches to the higher valve lift to achieve the engine's full power delivery.
Multiple fuel injection ensures optimum combustion despite the smaller valve lift. This compensates the reduced turbulence of the fuel/air mixture in the combustion chamber in the area of the spark plug. The four-cylinder has direct injection with latest-generation piezo injection valves. The position of the injectors has been optimised to achieve low cylinder wall coverage and therefore lower untreated emissions, especially particulate emissions. A particulate filter is included as standard. Thanks to optimised injection with partial valve lift, the engine runs even more quietly in wide operating ranges. A low level of exhaust emissions has been achieved by further development of the well-proven BlueDIRECT combustion system in conjunction with the standard petrol particulate filter.
The single-pipe turbocharger features an electronically controlled wastegate valve. The previously vacuum-operated actuator has been replaced by a precision electrical actuator, which reports its position and has a higher actuating speed, so that charge pressure control and diagnosis are significantly improved. This allows charging to be more precisely controlled.
The oil circuit is supplied with engine oil on a demand basis. Sensors monitor the oil pressure so that the supply volume can be adjusted. The cooling circuit has an electronically controlled thermostat which allows the engine temperature to be optimally set to suit needs.
To make engine operation more comfortable, a new centrifugal damper has been introduced into the powertrain as an addition to the balance shafts. This improves the engines NVH characteristics and allows comfortable driving possible at lower rpm. The exhaust system with flap control has the same purpose.
The engine is configured for front-wheel drive and 4MATIC all-wheel drive, and combined with the 7G-DCT dual clutch transmission. The M 260 engine is produced by the Kölleda plant.
The new OM 608 diesel engine: quieter and cleaner
The entry-level OM 608 diesel engine in the A 180 d is a new development based on the OM 607. It is more powerful (85 kW, 5 kW more), has further reduced emissions, complies with EU 6d temp including the new requirements relating to Real Driving Emissions – RDE, and has optimised noise characteristics.
New technological components include the improved turbocharger with variable turbine geometry integrated into the exhaust manifold. An electric actuator now adjusts the turbine geometry Together this makes for a more immediate charging response. The intake air is now cooled by an engine-mounted water intercooler.
The installed height of the new aluminium cylinder head has been reduced, and the moving masses of the valve assembly reduced. The intake manifold is now integrated into the cylinder head cover. The pressure of the common-rail injection system has been increased to 2000 bar (previously: 1600 bar). The electro-magnetically controlled injectors have eight injection holes. This allows precise combustion control by up to six injections per working cycle. Dual pre-injection is used to optimise combustion noise in wide operating ranges, and the injectors are sealed in their shafts.
The cast-iron engine block has been made lighter, while increasing its rigidity. Weight-optimised steel pistons are used as before. A demand-controlled oil pump is used, with a pressure regulating valve adjusting the oil pressure on the basis of need and temperature-dependent characteristics maps.
For sound insulation, the sump has a polyurethane foam cover, the engine cover an interior foam lining and the design cover an interior PET lining.
For low emissions, the OM 608 is equipped with high and low-pressure exhaust gas recirculation. The compact exhaust aftertreatment system is near-engine mounted. Alongside the oxidation catalytic converter and the particulate filter, SCR catalytic converters with AdBlue® metering are used for the first time in this engine class. The particulate filter also has an SCR coating. A large AdBlue® tank with a capacity of 23.8 litres ensures long refilling intervals, and has its own, externally accessible filler neck next to the diesel filler neck.
At market launch the engine is available with a new 7G-DCT dual clutch transmission. The OM 608 was developed as part of a strategic cooperation with Renault. The Mercedes-Benz specific technology components include:
- engine mounting
- special two-mass flywheel
- dual-clutch transmission
- alternator and air conditioner compressor
- engine control unit with specific software
- ECO start/stop function
Basic data of the new engines at market launch of the new A‑C lass:
|
|
|
M 282 |
M 260 |
OM 608 |
|
Cylinders |
Number/arrangement |
4/in-line |
4/in-line |
4/in-line |
|
Valves per cylinder |
Number |
4 |
4 |
2 |
|
Displacement |
cc |
1332 |
1991 |
1461 |
|
Displacement of one cylinder |
cc |
333 |
498 |
365 |
|
Cylinder spacing |
mm |
85 |
90 |
85 |
|
Bore |
mm |
72.2 |
83 |
76 |
|
Stroke |
mm |
81.4 |
92 |
80.5 |
|
Bore/stroke |
|
1.3 |
1.1 |
1.05 |
|
Rated output |
kW/hp |
120/163 |
165/224 |
85/116 |
|
at |
rpm |
5500 |
5500 |
4000 |
|
Peak torque |
Nm |
250 |
350 |
260 |
|
at |
rpm |
1620–4000 |
1800-4000 |
1750-2500 |
|
Specific output |
kW/l |
90 |
83 |
58 |
|
Compression ratio |
|
10.6 |
10.5 |
15.1 |
The 7G-DCT transmissions: comfortable and economical
In the new A-Class, Mercedes-Benz uses two different 7G-DCT dual clutch transmissions with a wet clutch: The previous transmission has been developed further for the more powerful engines (e.g. A 250). It has been improved in shift performance and reaction time by an optimised friction system and pistons with a lower hysteresis. To transfer the driver's shift commands even more directly, communication between the engine and transmission has been revised. Control of the available drive programs ECO, Comfort, Sport and Individual has also been adapted.
The A 200 and A 180 have a newly developed 7G-DCT dual clutch transmission. For a low dry weight of 67 kg, the actuators exhibit high mechanical and electrical efficiency. The gears are shifted electro-mechanically, the wet clutches are operated electrohydraulically. The software-controlled clutch allows different shift characteristics – from sporty to particularly comfortable – with the driver able to choose between ECO, Comfort, Sport and Individual. As further functions it allows extended coasting and ECO start/stop. This transmission was developed together with GETRAG, who is also the supplier.
Under the microscope: 4MATIC: More driving pleasure, more efficiency
On request the new A-Class is available with the permanent all-wheel drive system 4MATIC with fully variable torque distribution. This sporty all-wheel drive system has been developed further, and now offers even more driving pleasure and efficiency. Using the DYNAMIC SELECT switch, the driver is able to influence the 4MATIC characteristics even more than before.
4MATIC components include the power take-off to the rear axle, which is integrated into the automated dual clutch transmission, and the rear axle differential with an integrated multiplate clutch. This is no longer electro-hydraulically powered, but instead electro-mechanically.
Via a crown wheel and a ball ramp, an electric motor exerts an axial force on the clutch pack to open or close the plates. The rear axle differential compensates the different paths/rotational speeds of the rear wheels. The advantages of this control system are above all non-rpm-dependent operation across the entire actuation range, pilot control of the clutch while still stationary and higher efficiency thanks to the ball ramp concept.
Drive torque distribution between the front and rear axles is fully variable. Depending on the driving situation, 100 % of the drive torque can be directed to the front axle (e.g. when driving straight ahead with no increased slip at the front axle), or in borderline cases up to 100% can be directed to the rear axle if the friction coefficient suddenly changes.
Using the DYNAMIC SELECT switch, the driver is able to influence the characteristics of 4MATIC even more than before. In the A-Class there are two characteristic curves available for clutch control. Models equipped with 4MATIC have a four-link rear suspension.
Body and passive safety: Safety and quiet running at the highest level
A rigid and intelligently designed body provides the basis for both crash safety and pleasant acoustics. Safety is also enhanced by specifically deformable crumple zones, and quiet running by numerous other measures. Nonethelesss the weight of the bodyshell has been kept at the level of the preceding model.
The new A-Class is also the first Mercedes-Benz model to have been developed at the new Technology Centre for Vehicle Safety (TFS). The design of the vehicle structures incorporates findings from research into real accidents. Every single bodyshell component was developed according to the loads and stresses encountered, with respect to geometry, material thickness, joining technology and material quality (increased proportion of high-strength and ultra high-strength sheet steel).
The centrepiece of the body's safety concept is the highly rigid passenger cell. Its great rigidity when subjected to accident-induced stress e.g. in frontal, lateral or rear-end collisions and rollovers is above all due to the greater use of high-strength, ultra high-strength and press-hardened sheet steel.
The strength of the entire side wall is increased by a floor assembly with high transverse rigidity. In the front footwells this is brought about by two inner and one outer reinforcing section between the inner shell of the front side members and the central tunnel. There is a continuous seat cross-member in the rear. These are augmented by seats with high transverse rigidity featuring tubular sections in the seat frame.
The upper area of the B-pillar is extremely rigid, with hot-formed ultra high-strength steel, while the lower area is slightly less rigid with deformable, ductile steel. This gives the B-pillars very good deformation kinematics. The steel doors have specific reinforcements, and additional protection is provided by impact elements in the side seat and B-pillar claddings.
The so-called Inertia door handles are the result of in-house accident research. These even more reliably prevent a door from opening during an accident, as the door is locked in place at the handle when subjected to impact-induced forces.
Special measures for the structural safety of the vehicle's front section include the following:
- the robust firewall cross-member of hot-formed, press-hardened steel between the two A-pillars
- several parallel load paths for improved load distribution in a partial frontal collision (offset crash)
- side members at the upper impact level connected to the A-pillars
- effective load distribution from the front side members by means of specially reinforced A-pillars
- a middle impact level with side members having specific crash kinematics
- multi-layered floor structures for optimum energy absorption
- an additional pedal floor cross-member to protect the footwell
- continuous floor side members to improve energy transfer into the underbody structure, with a larger cross-section and material thickness than in the previous model
- compatibility with other vehicles in the design of the front structure in the event of a frontal collision (protection of other road users).
The more compact drive units also play an important role. During a frontal collision, and acting together with the body structure, they allow more homogeneous deceleration and help to ensure the occupant protection for which Mercedes-Benz is well-known. Depending on impact severity, the engine and transmission are specifically displaced and disengaged from the new integral carrier.
Vehicles with a tailgate require a particularly well-conceived rear body structure to compensate for the large aperture. For many years, e.g. in the
E-Class Estate models, the structural concept of two peripheral sections has proved successful for Mercedes-Benz: the so-called C-ring at the level of the
C-pillar and the D-ring around the tailgate aperture. Thanks to the geometry of the D-ring, it was possible to position the lower section of the C-ring completely below the rear floor while retaining the excellent rigidity of the previous model. This enlarged the load capacity and made a level load area possible.
Restraint systems: partnership with the safety bodyshell
The most important restraint system is the seat belt. The driver and front passenger each have a three-point seat belt with belt force limiter and belt tensioner. In conjunction with the PRE-SAFE® system (optional equipment), the front seats are equipped with reversible belt reel tensioners. Both of the outer rear seats are fitted with a seat belt with reel tensioner and belt force limiter. These excel with a relatively low level of force for small and lightweight occupants. The centre belt is a standard three-point belt.
The new A-Class is equipped with driver and front passenger airbags, a driver's kneebag and windowbags as standard. Unlike in many competing models, the windowbag also covers the A-pillar for more complete passenger protection. Thorax-pelvis sidebags are likewise standard in the front, and available as optional equipment for the rear.
Child safety: automatic deactivation of the front passenger airbag
A pressure sensor in the front passenger's seat cushion can detect whether the seat is unoccupied or whether an infant or other child seat has been placed on the front passenger seat, and in the latter case deactivate the front passenger airbag automatically. Contrary to other systems that require the airbag to be deactivated with a key, this system reduces the risk of incorrect operation. As no special transponder is required, the system can be used for all conventional, rear-facing child restraint systems. The system is standard or optional equipment depending on the market or region.
i-Size child seat attachments are used for i-Size child seats. This internationally standardised attachment system, the successor to Isofix, is provided for the outer rear seats as standard. It improves protection with a fixed connection between the child seat and the vehicle.
Pedestrian protection: active bonnet
Reducing the severity of an impact is particularly important in the case of a collision with vulnerable road users such as pedestrians, as these have no "crumple zone" of their own. This is where the active safety systems of Intelligent Drive come into their own. If an impact is unavoidable, the further developed measures to mitigate the consequences of accidents involving pedestrians can help.
The active bonnet is an important factor in this. The technical basis is a comprehensive sensor system in conjunction with intelligent algorithms in the airbag control unit, which decides when to trigger. After activation of the pyrotechnical actuators, the bonnet is raised on its hinge by a significant 80 mm or so within fractions of a second. This creates additional space between the bonnet and the components in the engine compartment. The protective effect is increased by a comparatively flexible cross-member below the windscreen. This is designed in the form of a shackle, enabling it to give way better in the event of a head impact.
Noise and vibrations: there is strength in serenity
Quiet, vibration-free driving characteristics are a major factor in the grown-up, premium driving impression made by the new A‑C lass. Alongside effective insulation of the suspension from the vehicle body (see section on Suspension) and aeroacoustic measures, the bodyshell itself plays a decisive role.
During the development of the new A-Class, particular attention was given to high overall structural rigidity and the connecting points between the body, suspension and powertrain. Significant increases in introduction rigidities were especially achieved at the suspension connecting points that are so important to road roar, and the interior noise level was considerably reduced.
Following examination of the previous model, the guide bearing of the front axle and the rear connection of the subframe were identified as major introduction points. The introductory rigidity at the front axle guide bearing was significantly increased with a compact, rigid integral carrier.
The subframe of the multi-link rear axle is elastically isolated by rubber bushings. The front subframe connection is integrated into the C-ring structure of the bodyshell, and therefore has the rigidity to isolate it. A cross-member is integrated into the multifunction recess to increase the introductory rigidity of the rear subframe connection. This not only gives transverse support to the subframe carrier, but also stiffens the membrane surface of the recess. This reduces sound radiation as a good basis for efficient noise insulation.
To reduce the noise impact to the passenger compartment, the firewall is a high-quality injection-moulded component. In contrast to deep-drawn components, this has the advantage that constant wall thicknesses are possible: large changes in contours do not thin out the material – a classic acoustic weak point. In addition a modular major assembly compartment partition made of plastic is used by Mercedes-Benz for the first time for a platform with transversely installed engines. This makes models with the top engine variants particularly quiet-running.
The comprehensive noise insulation concept of the new A-Class includes components such as the air and coolant management systems or trim parts in the interior being configured so as to improve noise insulation as well. Sound insulation measures also include the specific use of absorbers e.g. in the area of the C-pillars, in body cavities and with spring-mass systems on the wheel arches. The tool used for all sound insulation measures was statistical energy analysis (SEA). This makes it possible to assess the effect of sound insulation concepts at a very early stage with the help of computer models.
Suspension: Agile and comfortable
There is a choice of suspension systems for the new A-Class, depending on engine variant and driver preference. 16-inch wheels are standard equipment. DYNAMIC SELECT is standard equipment, and at the touch of a button also provides an individual driving experience in conjunction with active damping control (optional).
Like all its predecessors, the new A-Class has a McPherson front suspension. Wheel control is taken care of by one transverse control arm below the wheel centre, the McPherson strut and one tie rod. The transverse control arm in the new A-Class is a forged aluminium component. This reduces both weight and unsprung masses. The steering knuckles are made of cast aluminium.
The wheel-locating McPherson struts feature transverse force-optimised coil springs and twin-tube gas-pressure shock absorbers with auxiliary springs. The support bushing is a three-way design, with the forces applied by the damper, spring and auxiliary spring isolated from each other. Here too, attention was paid to low weight with a hollow piston rod, aluminium head bearing and a perforated spring plate. The tubular stabiliser is connected to the suspension struts by a newly developed, weight and friction optimised torsion bar linkage of hybrid polyamide construction.
When defining the axle geometry, particular attention was paid to keeping torque steer to a minimum and eliminating jolts as far as possible. The form and arrangement of the rubber bushings determines the great agility of the vehicle, also allowing a high level of ride comfort and driving safety.
Steering: also supports automated driving
The gearing of the electro-mechanical rack-and-pinion steering is located behind the wheel centre, and servo assistance is speed-sensitive as standard. The steering assistance function (in conjunction with the Driving Assistance package) is a new feature. The driver's steering movements to stabilise the vehicle are assisted by additional steering torque generated by the electric servo unit.
These include:
- countersteering in case of oversteer
- steering corrections when braking on varying road surfaces
(μ-split braking) - reducing the steering effects of front-wheel drive
- compensation for crosswinds and road camber.
In combination with Active Distance Assist DISTRONIC, transverse control takes place to add active lane-keeping to the intelligent cruise control.
Rear axle: four control arms, high proportion of aluminium
The more powerful versions of the new A-Class such as the A 250 and all 4MATIC models have a sophisticated four-link rear suspension. The three transverse arms and one trailing arm at each rear wheel are configured for maximum driving stability, comfort and longitudinal/lateral dynamics. The rear axle is mounted on a subframe isolated from the bodyshell by rubber bushings so that fewer vibrations are transferred from the suspension to the body.
The wheel carrier and spring control arm are made of aluminium – low unsprung masses allow a particularly sensitive "feel" for the road surface. All in all, the proportion of aluminium in the suspension components is one of the highest in any suspension system in this vehicle class. Newly developed shift rails made of polyamide connect the torsion bar stabiliser with the rear axle.
The entry-level A 200 and A 180 d models have a torsion beam rear suspension. Its U-section rotates in a targeted manner in one-sided compression and rebound, and acts as a stabiliser bar. The torsion-beam rear axle is secured to the body with two bearings and uses the same attachment points to the body-in-white as the multi-link axle's trailing arm.
Single-tube shock absorbers and separate coil springs are used for both the four-link and the torsion-beam rear axle. Here too, effective noise insulation of the coil spring between the body and rear axle is achieved with two elastomer insulators. The connection between the shock absorber and the body is via an aluminium bearing, which by way of its soft gimbal-type mount contributes to a reduction in friction in the damper and therefore to an improvement in response.
Three suspension variants: choice of setups
As standard the new A-Class is equipped with a comfort suspension with steel springs and DYNAMIC SELECT. The comfort suspension lowered by 15 millimetres has specially configured springs and dampers for more sporty characteristics.
The suspension with active damping control enables the driver to choose the preferred damping characteristics. A valve in each of the four shock absorbers is electronically actuated to control the oil flow. The damping characteristics are changed by regulation of the oil flow.
Several different sensors constantly monitor the suspension status, driving situation and driving style of the driver, and adjust the damping at each wheel. Information is also added by the engine, transmission, braking system, steering and driving assistance systems. The damping is specifically stiffened during acceleration, braking or steering manoeuvres to reduce pitching and body roll, and to improve wheel loads and tyre adhesion.
Brakes: ADAPTIVE BRAKE as standard
The new A-Class has a hydraulic dual-circuit braking system in X-configuration with the brake control function ADAPTIVE BRAKE as standard. The dimensions take vehicle-specific circumstances such as axle load distribution, weight and performance into account. The electric parking brake is standard equipment. The rear axle features a combined floating brake calliper with an electric parking brake function.
ADAPTIVE BRAKE puts technology from the top-of-the-line model Mercedes-Benz models into the A-Class. Thanks to electronic control, the hydraulic dual-circuit braking system allows assistance functions that improve safety and comfort. This includes priming of the braking system in critical situations: if the driver's foot moves abruptly from the accelerator to the brake pedal before an emergency stop, the braking system increases the pressure in the brake lines and brings the pads into contact with the brake discs so that maximum braking power is available as soon as the driver hits the brake pedal. This priming of the brakes allows the system to assist the standard Brake Assist.
ADAPTIVE BRAKE also brings safety benefits in wet conditions. The system briefly applies the brakes at regular intervals to wipe the film of water from the brake discs, ensuring that the brakes are able to perform at their peak. This automatic brake drying function is always activated when the windscreen wiper of the A-Class has been switched on for a certain time, and the finely metered braking impulses go unnoticed by the driver.
After braking to a standstill, briefly pressing the brake pedal a little further is all that is required to activate the HOLD function. The car is then held by the brakes, even if the driver's foot is taken off the brake pedal. In this way ADAPTIVE BRAKE prevents unintentional moving-off at traffic lights or in stop-and-go traffic, or rolling backwards on uphill gradients. The HOLD function is deactivated automatically when the car moves off.
The range of wheels and tyres begins at 16 inches. It comprises steel wheels in size 16 and 17 inches and light-alloy wheels in size 16 to 19 inches. The overall outer diameter of the wheels/tyres is 660 mm rather than the previous 645 mm.
*The above models have been certificated according to Euro 6d-TEMP.